The North American Fly Fishing Forum

The North American Fly Fishing Forum (http://www.theflyfishingforum.com/forums/)
-   Fly Rod Building (http://www.theflyfishingforum.com/forums/fly-rod-building/)
-   -   Dan Craft Five Rivers FT 10' 7wt (http://www.theflyfishingforum.com/forums/fly-rod-building/5916-dan-craft-five-rivers-ft-10-7wt.html)

mlwebb 09-15-2008 12:08 AM

Dan Craft Five Rivers FT 10' 7wt
 
Hi Folks,
This is the first fly rod I've built. When I was in Junior High or early High School (35 yrs ago), one of my buddies father taught us how to build a spinning rod, and helped us each build one, so I had some idea of what was involved, (Hey, teach a kid or two if you have the opportunity). Some diligent forum reading helped.
Reelseat and first cork ring glued on blank. The hole in the end is for a screw on small fighting butt.
http://www.mlwebb.com/images/reelseatthmb.jpg
My homebuilt rod building stand with cordless drill set up for turning cork. The little wheels on the rod supports (there are three of them, one on each side, one on a 1/4 inch ply arm, are furniture glides (six for $5). The stand is mdf I had around the house (leftover from speaker building, but that's another forum :) I glued the cork rings together and to the rod blank with Locktite "Sumo" polyeurathane glue. It claimed to foam less than its competitors, and seemed to work fine. I am sure Titebond III would also.
http://www.mlwebb.com/images/corklathethmb.jpg
Cork almost done. I don't know how long it takes you pro's to shape a handle, but it took me about 3 hours till I was happy with it. That includes a lot of squinting at it, and checking other fly grips around the house.
http://www.mlwebb.com/images/corklathe2thmb.jpg
Bottom striper at ferrule. I added a bit to the wrap to bring it over the spot on the female ferrule where the end of the male ferrule will be when rod is assembled. I read somewhere that this can be a stress spot, which made sense to me, so I reinforced it. The next image shows an upper ferrule, also with reinforcement.
http://www.mlwebb.com/images/ferrulethmb.jpg
http://www.mlwebb.com/images/ferrulewrapthmb.jpg
I looked at a couple of online guide spacing charts, downloaded a spreadsheet, and had the measurements that someone online (in Europe) had used with this blank. I decided to use a "tamer" stripper setup, with a sixe 12 about 5" above the bottom size 16. Using one of the calculators, I got a guide at each ferrule, 11 total. (4,9 5/16,15 7/16, 22 5/8, 30 3/4, 39 3/4, 49 5/8, 60 1/2, 72, 84 3/16, 89 1/2) I have no idea if this is ideal, but it looked good in a static test, and seems to work well.
Wrapping guides (using foran lock)
http://www.mlwebb.com/images/wrap1thumb.jpg
http://www.mlwebb.com/images/wrap2thumb.jpg
These ones at the rod tip get pretty skinney. This one needs a little packing. Both threads are NCP
http://www.mlwebb.com/images/guidewrap2thmb.jpg
This is my rod drying adaptor, a 6 rpm motor I stole out of an old microwave (It needed replacement, which I haven't got around to yet. I kinda miss it for warming up coffee)
http://www.mlwebb.com/images/microthmb.jpg
And here is the finished Rod. I used Threadmaster Lite. They sure have improved this part of rodbuilding.
http://www.mlwebb.com/images/green1thmb.jpg
I am very happy with the feel of the rod. As the "Common Cents" data suggested, the 10 foot DC FT's have a different action than the 9' rods, a little slower and truer to line wt. ( I measured 7.28/61). It seems to have a quick recovery, and throws the line well. (at least as well as my modest casting skills allow, need to work on that)
Michael

Silenttracker 10-05-2008 08:55 AM

Re: Dan Craft Five Rivers FT 10' 7wt
 
Well Done,
I like the "clean" wraps and not too "flashy" overall look.

Mike

fishincaper 11-30-2008 05:32 PM

Re: Dan Craft Five Rivers FT 10' 7wt
 
I recently built on a few of Dan Crafts blanks.The latest is a 10ft 8wt switch rod.A POWERHOUSE and it is very convenient to have a rod to convert to a 2 hander when it is needed.I also built on a Sig 4-5pc. A sweet trout rod.Dan sells great blanks.He is a good guy too.

mojo 12-08-2008 09:14 PM

Re: Dan Craft Five Rivers FT 10' 7wt
 
Very nice for being laid off for 35+ years. What's next on the list:smile:

jebson38 01-08-2009 12:47 PM

Re: Dan Craft Five Rivers FT 10' 7wt
 
Like the forhan lock...
Just started doing that on spinning stuff. Makes the single foots stay in place no matter what.


All times are GMT -5. The time now is 07:34 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0
2005-2014 The North American Fly Fishing Forum. All rights reserved.