Thanks Thanks:  0
Likes Likes:  2
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: Cortland Line-Leader Loop Connector

  1. Default Cortland Line-Leader Loop Connector

    Has anyone tried this? The package comes with 4 braided loops.

    Guess what? I have wasted 3 out of 4.

    Good thing the last piece I was able to do it right. No specific instructions on how to heat the "heat shrink plastic" piece, I use a regular lighter to heat it.
    - 1st: melted the brained loop;
    - 2nd: melted the fly line;
    - 3rd: almost perfect and not satisfied and try to shrink the plastic but ended up melting the braided loop again.
    - 4th: last piece: got it right but a bit tad loose on the on both end.

    I can't get this shrink properly. I should have just save my money and tie my own loop. LOL


    Don't eat fish... eat more chik'n

  2. #2
    Join Date
    Jun 2009
    Location
    Northern California
    Posts
    3,848
    Blog Entries
    4

    Default Re: Cortland Line-Leader Loop Connector

    Don't bother using heat shrink tubes. Tie a nail knot on the very end using 15 pound test line. That will create a better anchor.

  3. Likes williamhj liked this post
  4. #3
    Join Date
    May 2011
    Location
    Eagle River, AK
    Posts
    180

    Default

    I'd skip the connector and just nail knot some mono with a loop. The braided connectors seem to fail when it's most important.

  5. #4

    Default Re: Cortland Line-Leader Loop Connector

    If you have to use the heat shrink, try using a regular light bulb to shrink it. It's not as hot or unpredictable as an open flame.

  6. #5
    Join Date
    Aug 2012
    Location
    Portland and Maupin, Oregon
    Posts
    479

    Default Re: Cortland Line-Leader Loop Connector

    I use those loops for making T11 or T14 sink tips. I use them for making a loop to loop connection with a skagit shooting head for steelhead fishing. I slip the tip a couple inches into the braid and glue it with zap a gap. I nail knot a 1 ft. 40lb maxima mono but section on the other end and tie a loop on the other end of the mono. I loop on a 2 ft. 12lb leader. That's a standard set up for swinging flies in the PNW.

  7. Default Re: Cortland Line-Leader Loop Connector

    omg. I only slip in about half (1/2) inch of fly line into the braided loop and heat shrink the plastic tube. This may mean disaster when I fish with this.

    There's no more shrink tube left and I guess I will just cut it and tie nail knot with a 15 lbs mono in between the fly line and the Cortland braided loop.
    Don't eat fish... eat more chik'n

  8. Default

    This is how I intalled the braidd loop.




    Then i did a little tug on both ends and off it goes. I just tied nail knot with mono in between.

    Don't eat fish... eat more chik'n

  9. #8
    Join Date
    Sep 2011
    Location
    Sidney, Nebraska
    Posts
    480

    Default Re: Cortland Line-Leader Loop Connector

    I've tried different heat shrink loops and most have failed. I double over an inch of fly line and use 3 nail knots one after the other to create a loop. Sometimes I also use tying thread to whip finish a loop onto the line. Neither of these methods of loop making have failed me.

  10. #9

    Default Re: Cortland Line-Leader Loop Connector

    Bluebird, did you snake the fly line all the way into the connector to where the loop stops it? It is hard to tell by the pictures. You need as much fly line surface area in the braid as possible.
    Also, is the section of fly line super slim? This is a rough guess but by the picture it almost looks as skinny as the running line on some fly lines. Does the tip section taper up a little way past the tip?

  11. Default Re: Cortland Line-Leader Loop Connector

    Hi Jack, no. I just realized that I didnt snake all the way to the loop. only maybe about 1/2 inch into the braided. (mistake #1)
    Then I heated using the lighter and so afraid to melt the fly line and/or the braided loop. So you will see the shrink jacket tube is loose. (mistake #2).
    It seems that the fly line is about the right thickness. I had a hard time snaking it for that half inch. lol

    I am total noob when it comes to this.. lol
    Don't eat fish... eat more chik'n

Page 1 of 2 12 LastLast

Similar Threads

  1. How to make The Braided Connector For Your Welded Loop Spey Line;
    By Ard in forum Spey Fly Lines, Reels and other Spey Tackle
    Replies: 29
    Last Post: 01-26-2015, 08:28 PM
  2. fly line to leader loop
    By jspriddy in forum Fly Lines
    Replies: 16
    Last Post: 08-25-2012, 09:16 AM
  3. Replies: 0
    Last Post: 06-15-2012, 09:30 PM
  4. Replies: 0
    Last Post: 05-15-2012, 02:50 PM
  5. braided loop connector and nail knot
    By slduck in forum Fly Fishing Knots
    Replies: 2
    Last Post: 02-13-2012, 08:18 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •